Jm 1075-18R User Manual

OPERATOR’S MANUALGRAIN CARTSPATENTED SINGLE AUGERJ. & M. Mfg. Co., Inc.P.O. Box 547 Ft. Recovery, OH 45846Ph: (419) 375-2376 Fax: (419) 375-2

10TO THE OPERATOR(S)LOADING AND UNLOADING THE GRAIN CART1) With the gate indicator in the closed position, fill the tank with grain.2) With the PTO

11LUBRICATION SERVICE SCHEDULEIMPORTANT: Your Grain Cart has grease fittings at all critical points. These should be serviced before thecart is put

12TROUBLE SHOOTINGMAKE SURE THAT ALL POWER IS SHUT OFF BEFORE SERVICING THE GRAIN CART. MAINTENANCEAND REPAIR SERVICE WORK TO BE PERFORMED BY QUALIFI

13ADJUSTING THE SLIP CLUTCHADJUSTING THE LOWER FLIGHTING AND HANGER BUSHING ASSEMBLYMAKE SURE THAT ALL POWER IS SHUT OFF BEFORE ADJUSTING THE FLIGHTIN

14MAKE SURE THAT ALL POWER IS SHUT OFF AND THE UPPER AUGER TUBE IS IN THE DOWN POSITIONBEFORE REMOVING THE RESTRICTERS.Remove restricters from 90 degr

15HUB AND SPINDLE ASSEMBLYREPAIR PARTS LIST AND DIAGRAMSWhen performing maintenance work, wear sturdy, rough-soled work shoes and protective equip-men

16POWER TAKE-OFF SHAFT130 DEGREE GEARBOX ASSEMBLY# Part # Description28 19116 Pressure Plate29 00548 Bolt & Nut M10x10030 80039 Female Tube Yoke31

17DRIVE LINE ASSEMBLYUPPER AND LOWER AUGER ASSEMBLY# Part # Description1 LF-18 Lower Flighting welded to 4 1/2" pipe2 UF-18 Upper Flighting welde

18# Part # Description1 JD25024 2 1/2" x 24" Hyd. Cylinder2 JD469 Seal Kit for 2 1/2" x 24" Hydraulic Cylinder3 ICR4 1" x 4&q

19GRAIN CART ASSEMBLY# Part # Description1 FSH-18 Flow Control Spout Housing2 HP-18 Hinge3 BP-18 Baffle Plate4 HC-FCS Hydraulic Cylinder w/clevis end

2TO THE DEALER:J. & M. Mfg. Co. Inc. warrants against defects in construction or materials for a period of ONE year. We reserve the rightto inspe

20GRAIN CART LIGHT KIT# Part # Description1 8WH-7PC Main Wiring Harness with 7-Prong Connector End2 LE-1B Light Enhancer3 WH-1 Wiring Harness (Rear Ha

21#W/TPart # DescriptionW1 55WS Rear Weigh spindle with cable45WS Rear Weigh spindle with cable (Duals)2 278WS Front Hitch Weigh Bar with cable3 61591

22ELECTRONIC WEIGH SCALE SYSTEMS(FOR GRAIN CARTS EQUIPPED WITH TRACKS)#D/SPart # DescriptionD/S Qty1 ------- --------------- ---2 250WB Weigh Bar with

23BatteryWEIGH SCALE RETROFIT KIT(Continued)MOUNTING THE BATTERY BOXOn the rear side of the front, left leg of the grain cart (theleg below the auger

31075-18R GRAIN CARTSPECIFICATIONSDIMENSIONSA) 21”B) 178”C) 69”D) 233”E) 280”F) 162”G) 69”H) 149”I) 129”J) 14”K) 27”L) 146”M) 183”N) 154”O) 132”Note:

4GENERAL INFORMATIONBOLT TORQUE CHARTAlways tighten hardware to these values unless a different torque or tightening procedure is listed for a specifi

5TABLE OF CONTENTSINTRODUCTION 2EXPRESS WARRANTY 2SPECIFICATIONS 3GENERAL INFORMATION 3BOLT TORQUE CHART 4SAFETY RULES 6SAFETY SIGNS 7INITIAL OPERATIO

6SAFETYSAFETY RULESATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!Safety is a primary concern in the design and manufacture of our products. Unfo

7750-16 OWNER’S MANUALSAFETY SIGNSATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!Replace Immediately If Damaged or Missing!IMPORTANT: Install new

8The drawing shows the proper ways of mounting the wheels using Budd-type nuts. Thewheels supplied with your Grain Cart have straight holes and the B

9OPERATING INSTRUCTIONSBE CERTAIN THAT ALL POWER IS SHUT OFF WHEN HOOKING UP TO TRACTOR OR CONNECTINGHYDRAULIC LINES TO TRACTOR.Preparing the Grain Ca