Jm 1150-22S User Manual

OPERATOR’S MANUALGRAIN CARTSPATENTED SINGLE AUGERJ. & M. Mfg. Co., Inc.P.O. Box 547 Ft. Recovery, OH 45846Ph: (419) 375-2376 Fax: (419) 3

10IMPORTANT:1) Hookup grain cart to tractor using a good quality hitch pin. Attach a safety chain (not included as standardequipment) to the tractor

11LUBRICATION SERVICE SCHEDULEIMPORTANT: Your Grain Cart has grease fittings at all critical points. These should be serviced before thecart is put

12TROUBLE SHOOTINGMAKE SURE THAT ALL POWER IS SHUT OFF BEFORE SERVICING THE GRAIN CART. MAINTENANCEAND REPAIR SERVICE WORK TO BE PERFORMED BY QUALIFI

13ADJUSTING THE SLIP CLUTCHADJUSTING THE LOWER FLIGHTING AND HANGER BUSHING ASSEMBLYMAKE SURE THAT ALL POWER IS SHUT OFF BEFORE ADJUSTING THE FLIGHTIN

14MAKE SURE THAT ALL POWER IS SHUT OFF AND THE UPPER AUGER TUBE IS IN THE DOWN POSITIONBEFORE REMOVING THE RESTRICTERS.Remove restricters from 90 degr

15HUB AND SPINDLE ASSEMBLYREPAIR PARTS LIST AND DIAGRAMSWhen performing maintenance work, wear sturdy, rough-soled work shoes and protective equip-men

16POWER TAKE-OFF SHAFT130 DEGREE GEARBOX ASSEMBLY# Part # Description1 T-325 Gearbox Complete2 M56 2" Output Shaft w/30 Tooth Gear3 55X100 Double

17DRIVE LINE ASSEMBLYUPPER AND LOWER AUGER ASSEMBLY# Part # Description1 LF-22GS-146 Lower Flighting welded to 6" pipe x 146 1/4"2 UF-22GS U

18HYDRAULIC CYLINDER ASSEMBLY(To Raise and Lower the Upper Auger)BOLT ON HITCH ASSEMBLY# Part # Description1 SHW-112N-25Swivel Hitch Weldment (less pi

19GRAIN CART ASSEMBLYHYDRAULIC DRIVEN FLOW CONTROL SPOUT# Part # Description1 FSH-22NS Flow Control Spout Housing2 HP-22 Hinge3 BP-22RNS Baffle Plate4

2TO THE DEALER:J. & M. Mfg. Co. Inc. warrants against defects in construction or materials for a period of ONE year. We reserve the rightto inspe

20GRAIN CART LIGHT KIT# Part # Description1 8WH-7PC Main Wiring Harness with 7-Prong Connector End2 LE-1B Light Enhancer3 WH-1 Wiring Harness (Rear Ha

21#W/TPart # DescriptionW/T Qty1 55WS Rear Weigh spindle with cable 22 278WS Front Hitch Weigh Bar with cable 13 615915Indicator Box with mounting pla

22ELECTRONIC WEIGH SCALE SYSTEMS(FOR GRAIN CARTS EQUIPPED WITH TRACKS)#D/SPart # DescriptionD/S Qty1 ------- --------------- ---2 250WB Weigh Bar with

23BatteryWEIGH SCALE RETROFIT KIT(Continued)MOUNTING THE BATTERY BOXOn the rear side of the front, left leg of the grain cart (theleg below the auger

3MODELS 1050-22S and 1150-22S GRAIN CARTSSPECIFICATIONSDIMENSIONSA) 1’-6”B) 18’-10”C) 8’-6”D) 22’-0”E) 29’-7”F) 14’-4”G) 6’-4”H) 12’-0” (1050)12’-2” (

4GENERAL INFORMATIONBOLT TORQUE CHARTAlways tighten hardware to these values unless a different torque or tightening procedure is listed for a specifi

5TABLE OF CONTENTSINTRODUCTION 2EXPRESS WARRANTY 2SPECIFICATIONS 3GENERAL INFORMATION 3BOLT TORQUE CHART 4SAFETY RULES 6SAFETY SIGNS 7INITIAL OPERATIO

6SAFETYSAFETY RULESATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!Safety is a primary concern in the design and manufacture of our products. Unfo

7750-16 OWNER’S MANUALSAFETY SIGNSATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!Replace Immediately If Damaged or Missing!IMPORTANT: Install new

8The drawing shows the proper ways of mounting the wheels using Budd-type nuts. Thewheels supplied with your Grain Cart have straight holes and the B

9BE CERTAIN THAT ALL POWER IS SHUT OFF WHEN HOOKING UP TO TRACTOR OR CONNECTINGHYDRAULIC LINES TO TRACTOR.Preparing the Grain Cart for Use (see tracto