Jm 750-14 User Manual

OPERATOR’S MANUALGRAIN CARTSPATENTED SINGLE AUGERJ. & M. Mfg. Co., Inc.P.O. Box 547 Ft. Recovery, OH 45846Ph: (419) 375-2376 Fax: (419) 375-2

10OPERATING INSTRUCTIONS (Continued)LOADING AND UNLOADING THE GRAIN CART1) With the gate indicator in the closed position, fill the tank with grain.2

11LUBRICATION SERVICE SCHEDULEIMPORTANT: Your Grain Cart has grease fittings at all critical points. These should be serviced before thecart is put

12TROUBLE SHOOTINGMAKE SURE THAT ALL POWER IS SHUT OFF BEFORE SERVICING THE GRAIN CART. MAINTENANCEAND REPAIR SERVICE WORK TO BE PERFORMED BY QUALIFI

13ADJUSTING THE SLIP CLUTCHADJUSTING THE LOWER FLIGHTING AND HANGER BUSHING ASSEMBLYMAKE SURE THAT ALL POWER IS SHUT OFF BEFORE ADJUSTING THE FLIGHTIN

14If the upper and lower flighting still does not separate properly during the folding sequence, a small bevel mayneed to be ground out of the inside

15HUB AND SPINDLE ASSEMBLYREPAIR PARTS LIST AND DIAGRAMSWhen performing maintenance work, wear sturdy, rough-soled work shoes and protective equip-men

16# Part # Description1 91-1400-F-138 Front Half of PTO (1 3/8")2 91-1400-F-134 Front Half of PTO (1 3/4")3 97-18615B Back Half of PTO4 03-1

17DRIVE LINE ASSEMBLYUPPER AND LOWER AUGER ASSEMBLY(Not Shown)# Part # Description1 UF-14-F6R Upper Flighting welded to 2 1/2" pipe2 LF-14-F5R Lo

18HYDRAULIC CYLINDERHITCH ASSEMBLY# Part # Description1 JD25024 2 1/2" x 24" Hyd. Cylinder2 JD469 Seal Kit for 2 1/2" x 24" Hyd. C

19GRAIN CART ASSEMBLY# Part # Description1 FSH-14 Flow Control Spout Housing2 HP-14 Hinge3 BP-14 Baffle Plate4 HC-FCS Hydraulic Cylinder w/clevis end

2TO THE DEALER:J. & M. Mfg. Co. Inc. warrants against defects in construction or materials for a period of ONE year. We reserve the rightto inspe

20GRAIN CART LIGHT KIT# Part # Description1 8WH-7PC Main Wiring Harness with 7-Prong Connector End2 LE-1B Light Enhancer (108060)3 WH-1 Wiring Harness

21Installation of Scale Kit (Single Wheel Applications)For Models 525-14W, 620-14, 750-14, 750-16, 750-18, 875-16 and 875-18Remove the 2 1/2” x 13 1/4

22Installation of Scale Kit (Single Wheel Application)For Models 525-14W, 620-14, 750-14, 750-16, 750-18, 875-16 and 875-18Using the Junction Box as a

23Installation of Scale Kit (Single Wheel Application)For Models 525-14W, 620-14, 750-14, 750-16, 750-18, 875-16 and 875-18LAYOUT DIAGRAMPARTS LIST(We

24Grain Cart Roll Tarp Parts List and Set Up InstructionsPARTS LIST# Part # Description Qty1 525CT Tarp w/ Rivets (525)

25# Part # Description Qty11 TSB-1 Tarp Stop Bracket(525 thru 875, 1075) 3Tarp Stop Bracket(1000 thru 1326) 312 316C-150

26SET-UP INSTRUCTIONSRoll Tarps for Grain CartsPlace Tightening Lip on top of low side of graintank and clamp ends with a vise grips. (NOTE:Grain Car

27SET-UP INSTRUCTIONS (Continued)Roll Tarps for Grain CartsLocate the pre-punched holes in the End Panelsand drill 3/8” holes through the grain tankex

28Attach the Crank to the Universal Joint using 1/4” x2 1/2” hex bolt and 1/4” lock nut. Attach the UniveralJoint to the 1 1/4” Roll Tube using one 3

29SERVICE / MAINTENANCE RECORD DATE DESCRIPTION NOTES

3750-14 GRAIN CARTSPECIFICATIONSDIMENSIONSA) 18”B) 153”C) 69”D) 168”E) 229”F) 150”G) 76”H) 134”I) 120”J) 18”K) 24”L) 120”/144”M) 144”/160”N) 141”O) 12

4GENERAL INFORMATIONBOLT TORQUE CHARTAlways tighten hardware to these values unless a different torque or tightening procedure is listed for a specifi

5INTRODUCTION 2EXPRESS WARRANTY 2SPECIFICATIONS 3GENERAL INFORMATION 3BOLT TORQUE CHART 4SAFETY RULES 6SAFETY SIGNS 7INITIAL OPERATION 8OPERATION 9-10

6SAFETYSAFETY RULESATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!Safety is a primary concern in the design and manufacture of our products. Unfo

7750-16 OWNER’S MANUALSAFETY SIGNSATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!Replace Immediately If Damaged or Missing!IMPORTANT: Install new

8The drawing shows the proper ways of mounting the wheels using Budd-type nuts. Thewheels supplied with your Grain Cart have straight holes and the B

9IMPORTANT:1) Hookup grain cart to tractor using a good quality hitch pin. Attach the safety chain (not included as standardequipment) to the tracto