Jm 4WS17 User Manual

US-Rev:6/27/20134WS154WS17OPERATOR’S MANUALJ. & M. Mfg. Co., Inc.P.O. Box 547 Ft. Recovery, OH 45846Ph: (419) 375-2376 Fax: (419) 375-2708www

9rear axle24531167181091213151614

10SPIndle & tIre aSSemblIeS# Part. No. Description1 JM0001606 1-1/4” Hex Nut2 JM0009455 3/4” Bushing3 JM0003181 3/4” Shoulder Bolt4 JM0003184 3/4

11lIGht kIt aSSembly15114311413275641217161098# Part. No. Description1 JM0001595 1/2”-13 x 7” Grade 8 Hex Bolt2 JM0001393 Extension Bracket3 JM0001440

12uPPer bar dImenSIonSABCD4WS15-32 4WS15-38 4WS15-42 4WS17-48A32’ 38’ 42’ 48’B26.3’ 26.3’ 26.3’ 29.5’C25.8’ 25.8’ 25.8’ 28.5’D26.3’ 26.3’ 26.3’ 29.5’#

13SPecIfIcatIonSSPecIfIcatIonSWeight 3,120 lbsCapacity (NET) 13,000 lbs.Spindle Size 2” Diameter (sleeved)Hubs 8 BoltWheel Size 16” x 6”Tire Size 235/

14lIGht kItThis section of the harness is smaller in proportion to the rest of the harness for view-ing improvement. 12345# Part. No. Description1 JM0

15Set uP InStructIonSSet both of the bottom frame bars on two sawhorses or blocks. front & rear axleSAttach the front and rear axle to the frame b

16tIre InStallatIonAttach all four wheels. Use (8) 9-16” - 18 lug nuts to install the tires. Tighten lug nuts in a star pattern.Attach the Slide Bar W

17PuSh Pull Weldment barSlIde bar Weldment (cont’d)Attach the Push Pull Weldment Bar. Slide the bar through the Slide Bar Weldment. Use (2) 3/4” steel

18adjuStable header mountSSIde bar WeldmentInstall the adjustable support arms. Use (5) 5-8” Pin to attach the adjustable header mount to the frame. A

1TABLE OF CONTENTS2 To The Dealer3-4 General Information5 Safety Rules6 Tongue Assembly7-8 Brackets & Mounts9-10 Rear Axle, Spindle & Tires11

19header Saddle mountInstall the Header Saddle Mount. First set the mount onto the left frame. Run the 5/8” x 6 1/2” carriage bolt through the bottom

20tonGueAttach the tongue to the header wagon. First attach the outer tongue weldment to the front axle. Use a 6” 1 1/4” king pin weldment and a 1 1/4

21toP barInstall the top bar using (4) 1/2” hex nuts and (4) 1/2” USS at washers.extenSIon barInstall the extension bracket using (4) 1/2” x 7” grade

22lIGht barInstall the light bar using (4) 1/2” x 2” grade 8 hex bolts, (4) dampers, and (4) 1/2” grade 5 center lock hex nuts. Tools Needed:3/4

23WIrInG harneSS1) Run the short harness, starting with the 4 way at connectors go through the light bar starting on the side nearest to the rear ax

24 InItIal oPeratIon / maIntenance InItIal oPeratIon / maIntenancebe certaIn that all PoWer IS Shut off before ServIcInG the header tranSPor

MADE IN AMERICA

MADE IN AMERICA

2 Read manual instructions and safety rules. Make sure all items on

3General InformatIonTO THE OWNER:The purpose of this manual is to assist you in operating and maintaining your header wagon in a safemanner. Read it c

4GENERAL INFORMATIONBOLT TORQUE CHARTAlways tighten hardware to these values unless a different torque or tightening procedure is listed for specic a

5Safety ruleSATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!• Safety is a primary concern in the design and manufacture of our products. Unfortunat

6tonGue aSSembly# Part. No. Description1 JM0003033 Flapper Weldment2 JM0001688 Flapper Spring3 JM0001652 Roll Pin4 JM0001683 Flapper Tongue Weldment5

7bracketS & mountS4231571098111213161523191420212224171814628

8bracketS & mountS# Part. No. Description1 JM0003084 2” Ratchet2 JM0003061 3/8” USS Flat Washer3 JM0001485 3/8”-16 x 3/4” Hex Bolt4 JM0001594 1/2”